New Construction Plumbing in Albuquerque, NM

Reliable New Construction Plumbing Services in Albuquerque, NM

Fixture Installation and Trim-Out in Albuquerque, NM

Once the rough-in is complete and walls are up, our team returns for fixture installation and trim-out. This includes connecting sinks, toilets, bathtubs, showers, dishwashers, and water heaters. We ensure all fixtures are properly seated, sealed, and functional, providing a clean finish to your new construction plumbing. We work with many brands like Moen, Kohler, and American Standard to match your design specifications.

Fixture Installation and Finishing in Albuquerque, NM

Once the rough-in is complete and walls are up, GVK Plumbing handles the final installation of all plumbing fixtures. This includes sinks, toilets, showers, bathtubs, dishwashers, and washing machines. We ensure everything is properly aligned, sealed, and fully functional, providing a polished finish to your new home's plumbing system.

Underground and Under-Slab Plumbing in Albuquerque

The underground phase sets the drain, waste and vent layout that every fixture in the house will depend on. We trench, bed and slope PVC or ABS drain lines at a minimum quarter inch per foot and protect every pipe that passes through the slab or foundation with sleeves. Caliche, a hard, cement-like soil layer, is common in New Mexico and can make digging for sewer and water line repairs slow work. We compact bedding carefully and avoid rigid points that could stress the pipe as the ground moves. Each line is water tested and left exposed for the inspector before your concrete contractor pours.

Rough-In and Top-Out Plumbing in Albuquerque, NM

Once framing is up, we run supply and vent lines through the walls and attic and set every stub-out for sinks, tubs, showers and appliances. We usually install PEX-A with a central manifold so each fixture gets its own line and shutoff. Shower valves are set at the heights you choose, and tub sets are installed and protected before the drywall goes on. A full pressure test is held for inspection so nothing hidden in the walls is ever in doubt.

Permits and Inspections for New Plumbing in Albuquerque, NM

GVK Plumbing handles all required plumbing permits and coordinates with local Albuquerque inspectors throughout the new construction process. We make sure every phase of the plumbing installation, from rough-in to final trim-out, passes inspection. Our expertise in local regulations means your project stays compliant, avoiding delays and ensuring the long-term validity of your plumbing system.

Water Heater and Recirculation Installation in Albuquerque, NM

New homes commonly use tank water heaters in the garage, basement or utility room, or tankless units on an exterior wall. We size the heater to your bathroom count and install gas or electric connections, venting, an expansion tank and drain pan where required. Many owners add a dedicated recirculation line during rough-in, which is much less expensive than retrofitting later. Water across New Mexico is generally hard and mineral-heavy, so scale accumulates quickly in water heaters, faucets and appliance valves. If treatment makes sense for your water, we recommend planning space for a softener or filter loop at the same time.

Residential New Build Plumbing in Albuquerque

For new homes, our residential new construction plumbing includes the complete installation of water supply lines, drain waste vent systems, and gas lines. We ensure proper sizing and pressure for all fixtures, from showers to kitchen sinks, while accounting for local water quality and potential foundation movement. Water across New Mexico is generally hard and mineral-heavy, so scale builds up quickly in water heaters, faucets and appliance valves. Our process includes careful planning to prevent future slab leaks or drainage issues tied to the soil under your lot.

Final Trim and Fixture Setting in Albuquerque

At trim we install toilets, faucets, garbage disposals, dishwashers, ice maker boxes and laundry connections. We work with fixtures from Moen, Delta, Kohler, American Standard and the other brands builders commonly specify, or with owner-supplied fixtures. Every fixture is checked for flow, drainage and leaks, and angle stops are set straight and tight. We finish by running every fixture at once to confirm the system drains and vents properly under load.